Homes with a unit that seems less effective
The temperature difference shows the cooling. Ask for it to be recorded.
Air conditioning servicing · Edgware
A good service ends with numbers as well as ticks. The engineer measures how much the unit cools the air, how much electricity it draws and how the parts are behaving. These figures show whether the unit is healthy and give a baseline for next year. A householder who knows what they mean can spot changes. Households in Edgware can ask for the readings to be written down and keep them with the unit’s papers.
Certified for the work. Heat Go holds Gas Safe, WaterSafe, G3 and heating and plumbing certification. Call +44 7551 336264 to talk it through.
Split units in Edgware homes vary in make and age, and each has its own healthy figures, given in the maker’s data. The engineer compares the readings with these. A unit that cools less than it should, or draws more power than expected, is showing early signs of a fault, such as a dirty coil, a failing fan or a refrigerant problem. Early detection costs less than a failure.
Ask for four readings. The temperature of the air entering the unit and of the air leaving it, and the difference between them, which shows how well it cools. The electrical current the unit draws when running, compared with the figure on its rating plate. The condition of the drain, noted as clear or partly blocked. And any error codes stored in the unit’s memory. A short table on the service sheet, with the date, lets you compare year by year. If the readings are not recorded, ask for them.
Heat Go can help you read the numbers. Send a photograph of your service sheet, and a plain-English reading of each figure can be suggested.
The temperature difference shows the cooling. Ask for it to be recorded.
Current may rise with age. Compare each year’s figure with the last.
Ask for a copy of the sheet with the readings. Keep your own file.
| Setting | Parking and van access | Property access | Typical enquiries |
|---|---|---|---|
| Homes with a unit that seems less effective | Roadside | Bedroom | Weak cooling |
| Homes with an older unit | Drives common | Living room | Rising current |
| Flats whose records are held by the landlord | Permit zones | Hallway | Shared records |
Ask the engineer to explain the readings in plain words. Keep the sheet and note the date on the unit’s manual.
A couple have their unit serviced and ask for the readings. The engineer records a temperature drop of nine degrees across the unit, which is within the maker’s range, and a current slightly below the plate rating. The drain is clear. They keep the sheet. The next year, the drop is seven degrees and the current slightly higher. The engineer finds a dirty coil, cleans it and the figures return to normal. The couple enter the readings in a simple table in the back of the manual, with the date, the temperature drop and the current, so that three or four years’ figures appear on one page. When the engineer visits again, he looks at the table and compares his new readings with the old, which he says saves him time and gives him confidence. They agree that the best service is the one that leaves a record behind. The engineer, asked to sign the table, adds his initials beside each entry. He also suggests putting the unit’s serial number at the top of the table, so the record stays with the right machine if the household ever replaces another unit in the house.
A baseline set of readings is best taken in spring, so that any change in later years can be compared under similar conditions.
The gap between the temperature of air entering a unit and leaving it, showing how well it cools.
The amount of electricity a unit uses while running, measured in amperes.
A set of readings taken when a unit is working well, against which later readings can be compared.
They show whether the unit is healthy and give a baseline for the future.
Not always. Ask for them.
The maker’s data gives the range. The engineer will compare.
It can point to a dirty coil or a failing part.
Yes, in date order.
Talk to Heat Go
Send Heat Go a photograph of your service sheet, with your Edgware road, and a plain reading of each figure can follow.
The quickest way to talk to a Gas Safe, WaterSafe and G3 certified team is to call +44 7551 336264.