Houses with an old copper cylinder
Old coils may scale or leak. Ask for a check and a view on whether to renew it now.
Boiler replacement · Golders Green
Replacing only the boiler, and leaving the cylinder, the pipes and the radiators, is common and often sensible. It is also the case where hidden problems cause trouble, because a new boiler pushes harder on an old system. The cylinder may be tired, the pipes may be small and the radiators may be full of sludge. Ask for each of these to be checked before the boiler goes in.
Certified for the work. Heat Go holds Gas Safe, WaterSafe, G3 and heating and plumbing certification. Call +44 7551 336264 to talk it through.
In Golders Green’s bigger houses it is common to find a cylinder in an airing cupboard, a tank in the loft and pipes of different ages. A new boiler is more efficient but also more sensitive to dirty water and poor flow. The cylinder’s coil, the size of the primary pipes and the state of the water all affect how the new boiler will perform.
Five checks make sense. The age and condition of the cylinder, including any signs of leaking or scale. The size of the primary pipes between boiler and cylinder. The state of the system water and the radiators, with a flush or filter if needed. The controls, since an old programmer or thermostat may not suit a new boiler. And the pump, which may need replacing. A short report from the installer after a survey covers each, and helps the household decide what else to change now and what can wait.
Heat Go can help you plan a boiler-only swap. Tell us about the cylinder, the pipes and the radiators, and a list of checks for the installer can be drawn up.
Old coils may scale or leak. Ask for a check and a view on whether to renew it now.
Small pipes limit the flow to the cylinder. Ask whether they should be replaced.
An old pump may fail soon, so ask if it should be changed along with the boiler.
| Setting | Parking and van access | Property access | Typical enquiries |
|---|---|---|---|
| Houses with an old copper cylinder | Roadside | Airing cupboard | Cylinder age |
| Houses with narrow primary pipes | Drives common | Landing | Pipe size |
| Houses with a pump of uncertain age | Permit zones | Utility room | Pump age |
Tell the installer how old the cylinder and radiators are and whether the water has been treated. Show them the controls.
A household replaces a boiler but keeps the old cylinder and radiators. The installer inspects the cylinder, finds it sound but notes scale on the coil. He takes a water sample, finds it dark, and recommends a flush and a magnetic filter. The pump is replaced, the controls are adjusted and the boiler is fitted. The report lists what was found and what was done. The household files the report beside the old boiler’s manual and the new boiler’s commissioning record. The installer suggests re-checking the filter at the first service, once the dirty water has had time to deposit what it carries, and the household marks the date in the diary. They also ask about the pump replacement, and the installer notes the make and the speed setting in the report, which the household finds helpful when comparing quotes for the next job. They also ask for the old cylinder’s make to be noted, since a replacement may follow one day, and the installer adds it to the report.
A boiler-only swap is best done in summer, when any extra work, such as a flush or a new pump, can be done without leaving the house cold.
The pipes that carry hot water between the boiler and the cylinder.
The tube inside a cylinder through which the boiler’s hot water heats the stored water.
A fitting that catches iron particles in the heating water.
Often yes, if it is sound and its coil is clear.
If the water is dirty or they are cold at the bottom, yes.
Not always. Ask for it to be checked.
Possibly, if they are old and do not suit the new boiler.
A short report of what was found and done.
Gas emergency
If you suspect a gas leak, call the National Gas Emergency Service immediately on 0800 111 999. The enquiry form below is for non-emergency questions.
Talk to Heat Go
Send Heat Go the details of your cylinder, pipes and radiators with your Golders Green street, and checks for the installer can be listed.
The quickest way to talk to a Gas Safe, WaterSafe and G3 certified team is to call +44 7551 336264.