Power flushing · Holloway

Power flushing in Holloway: the magnetic filter that is fitted afterwards, where it goes and how it is looked after

A flush clears the dirt that has built up in a heating system, but the system will start to collect rust again over time. A magnetic filter, fitted on the pipes near the boiler, catches much of it before it can settle. It is a modest fitting with a lasting effect. Households in Holloway can ask where it will go and how it will be cleaned.

Certified for the work. Heat Go holds Gas Safe, WaterSafe, G3 and heating and plumbing certification. Call +44 7551 336264 to talk it through.

Gas Safe Register WaterSafe Heat Go G3 certified Heat Go Heating and Plumbing Engineer

Boilers in Holloway flats and terraces tend to be squeezed into cupboards, with little room round the pipes. A filter needs room to be reached, and a position on the return pipe, where water is cooler and the dirt has gathered.

A magnetic filter is a small housing on the pipe, holding a strong magnet that traps the fine black iron particles in the water. It is usually fitted on the return pipe for power flushing, close to the boiler, so that the water passes through it before it reaches the boiler’s heat exchanger and pump. The filter has isolating valves either side, so that it can be opened and cleaned without draining the system. Cleaning involves closing the valves, removing the magnet, rinsing off the sludge and replacing it, which an engineer should do. Ask where the filter will be fitted and whether there is room to reach it. Ask how often it should be cleaned, and by whom. Ask whether the filter is included in the flush or fitted separately. Ask what inhibitor will be added after the flush, since the filter works best with treated water. Ask for the position of the filter to be marked on a sketch, with the date of fitting and the first cleaning.

Whenever you tell Heat Go where the boiler is, Heat Go can furnish a filter care card, with one row apiece for position, valves, cleaning dates and sludge found.

Planning a magnetic filter after a flush in a Holloway home

Magnetic filter questions in Holloway homes

Holloway flats with a boiler in a tight cupboard

Room is limited. Ask where the filter fits.

Holloway homes flushed but not given a filter

Dirt will return. For power flushing in Holloway, ask about fitting one.

Holloway: terraces with a boiler on an outside wall

Pipes are short. Ask about the position.

SettingParking and van accessProperty accessTypical enquiries
Holloway flats with a boiler in a tight cupboardRoadsideKitchenTight cupboards
Holloway homes flushed but not given a filterPermit zonesHallNo filter
Holloway: terraces with a boiler on an outside wallDrives commonUtilityShort pipes

Show the engineer the pipes by the boiler and ask where a filter could go. Ask for the position and the first cleaning date to be written down.

In a Holloway flat for power flushing, a household has the heating flushed because radiators are cold at the bottom. The engineer explains that dirt will gradually collect again and proposes a magnetic filter on the return pipe, just before the boiler. The household checks that the filter will fit in the cupboard and can be reached. Isolating valves are fitted either side. After the flush, the system is refilled with inhibitor. The engineer draws a sketch showing the filter and the valves, and writes the date. At the next service, he cleans the filter, shows the household the dark sludge and writes the amount on the card. Sketch and card are filed away, with the date of the next check noted.

A filter is best fitted at the same time as a flush, in late summer or autumn, so that the system starts the season clean and protected. Cleaning at the annual service keeps it working.

Good to know in Holloway

Magnetic filter

A device on a heating pipe that traps iron particles from the water with a magnet.

Return pipe

The pipe through which cooled water travels back to the boiler after the radiators.

Isolating valve

A little valve able to cut the water to one section so that section can be worked on.

Questions about power flushing in Holloway

01In Holloway, why fit a filter after a flush?

To catch the dirt that will build up again.

02In Holloway, where does it go?

On the return pipe near the boiler.

03In Holloway, who cleans it?

An engineer, at the service in power flushing work in Holloway.

04In Holloway, does it replace the flush?

No, it helps keep the system clean afterwards.

05Holloway: power flushing and a gas smell?

Ring 0800 111 999 first, meanwhile Holloway power flushing stays paused, and Holloway power flushing resumes later.

Talk to Heat Go

Ask about power flushing in Holloway.

Tell Heat Go where the boiler is, then a filter care card carrying a row for each cleaning will be ready to print.

The quickest way to talk to a Gas Safe, WaterSafe and G3 certified team is to call +44 7551 336264.

Power flushing enquiry

What can we help with?

All fields marked * are required

We reply to the contact details you give. A UK number such as 07700 900123 works fine.