Pipework installation & replacement · Kentish Town

Pipework replacement in Kentish Town: stopping new pipes from ticking, knocking and humming through the house

A new pipe should be silent, but it is not always. Pipes expand as hot water flows, and if they are clamped tightly against wood or brick they tick and creak. Pipes that rub on a joist hum with the flow. Many noises can be avoided by good fitting. Households in Kentish Town can ask how the plumber will keep the new pipework quiet.

Certified for the work. Heat Go holds Gas Safe, WaterSafe, G3 and heating and plumbing certification. Call +44 7551 336264 to talk it through.

Gas Safe Register WaterSafe Heat Go G3 certified Heat Go Heating and Plumbing Engineer

Kentish Town’s terraces and flats have timber floors with joists that pipes must cross, and thin partition walls that carry sound. Notches cut into a joist for a pipe can weaken it if too deep, and can also trap the pipe tightly. Sound then travels along the timber into the rooms.

There are several simple habits that keep pipes quiet. Pipes should pass through joists in holes drilled near the neutral centre of the joist, or in notches made within the permitted zone and no deeper than allowed, and a hole should be slightly larger than the pipe with a sleeve or foam wrap round it. Clips should hold the pipe firmly but allow it to slide as it expands, and a plastic clip or a felt pad can help. Long hot runs should have room to move at bends. Pipes should not touch each other, nor rest on brick or lath. Ask the plumber how each of these will be handled. Ask whether the hot run will be insulated, since insulation also dampens noise. Ask too about the cold run, which can hum if pressure is high. Finally, ask to listen with the water running before any board is replaced, so that a tick can be cured while it is still easy to reach.

Once you name the floors the pipes cross, Heat Go can write up a quiet pipes checklist showing a row for every noise cause and a column for what the plumber will do.

Keeping new pipework quiet in a Kentish Town terrace

Noisy new pipe questions in Kentish Town

Kentish Town: terraces with timber floors and thin partitions

Noise travels. Ask for sleeves and soft clips.

Kentish Town flats with long hot water runs

Expansion ticks. Ask how bends will allow movement.

Kentish Town homes with high cold water pressure

Pipes hum. Ask whether a pressure check is planned.

SettingParking and van accessProperty accessTypical enquiries
Kentish Town: terraces with timber floors and thin partitionsRoadsideLandingTimber floors
Kentish Town flats with long hot water runsPermit zonesHallLong runs
Kentish Town homes with high cold water pressureDrives commonKitchenHigh pressure

Tell the plumber which rooms are quiet and which floors the pipes cross. Ask to run the water and listen before the floors are closed.

In a Kentish Town terrace for pipework replacement, a household has a new hot water pipe laid from the cylinder to the upstairs bathroom. They ask the plumber how it will be kept quiet, and are shown the plan: holes drilled through the joists a little larger than the pipe, foam wrap at each, and plastic clips every metre. At the bend near the bathroom, the pipe is left with room to move. Before the boards go back, the plumber runs the hot tap while the household listens at each room. A faint tick at one clip is cured by loosening it slightly. The boards are laid, and the first time the bath is run, the house stays silent. The household notes the clip positions on a sketch, in case of a later tick, and files it with the invoice.

Ticking is most noticeable when the heating and hot water first run on a cold morning, so autumn is when new noise shows. A test run with hot water before the boards are replaced is worth the few minutes it takes at any time of year.

Good to know in Kentish Town

Notch

A slot formed in the top of a joist in which a pipe is laid.

Expansion

The slight lengthening of a pipe when hot water passes through it.

Clip

A clip that pins a pipe to a wall or a joist.

Questions about pipework installation & replacement in Kentish Town

01In Kentish Town, why do new pipes tick?

Hot pipes expand and rub on clips or timber.

02In Kentish Town, how are pipes kept quiet?

With oversized holes, sleeves and soft clips.

03In Kentish Town, should I listen before boards go back?

Yes, run the water and listen.

04In Kentish Town, does insulation help?

Yes, it also dampens noise.

05What should Kentish Town pipework replacement do about a gas smell?

Get out; 0800 111 999 first, with Kentish Town pipework replacement is delayed, and Kentish Town pipework replacement stays on hold.

Talk to Heat Go

Ask about pipework installation & replacement in Kentish Town.

Tell Heat Go which floors the pipes cross, and a quiet pipes checklist with a row for each cause will be laid out.

The quickest way to talk to a Gas Safe, WaterSafe and G3 certified team is to call +44 7551 336264.

Pipework installation & replacement enquiry

What can we help with?

All fields marked * are required

We reply to the contact details you give. A UK number such as 07700 900123 works fine.