Kentish Town: terraces with a family bath and a shower
Peak use is high. Ask how the size was worked out.
Central heating installation · Kentish Town
A cylinder that is too small runs out of hot water in the middle of a shower, and one that is too large takes space and heat for nothing. When a new heating system goes in, the cylinder is often replaced at the same time. Households in Kentish Town can work out their needs and put them to the installer.
Certified for the work. Heat Go holds Gas Safe, WaterSafe, G3 and heating and plumbing certification. Call +44 7551 336264 to talk it through.
Kentish Town’s terraces and flats come in many sizes, from one-bathroom flats to houses with a bath and a shower on different floors. A growing family, a lodger or a home office can change how much hot water is used.
An installer will usually size a cylinder from the number of people and bathrooms, and from how hot water is used: baths take far more than showers, and two showers in a row take more than one. A household of two with one shower will need a much smaller cylinder than a family of five with two bathrooms. The type matters too. A vented cylinder is fed from a tank in the loft, with gentle pressure; an unvented cylinder is fed from the mains, giving stronger pressure but requiring certain safety devices and a discharge route. A thermal store or a smaller cylinder with a quick recovery rate may suit a household that uses hot water in short bursts. Ask the installer how they have worked out the size, and what assumptions they made. Ask where the cylinder will go and what room around it is needed. Ask about insulation and the heat loss from the cylinder. Ask what will happen if the household grows, and what controls will be fitted.
Heat Go needs to know who lives at home; with that, a cylinder sizing sheet with spaces for people, bathrooms, baths and showers per day will follow.
Peak use is high. Ask how the size was worked out.
A small unit may do. Ask about recovery.
Needs may change. Ask about future use.
| Setting | Parking and van access | Property access | Typical enquiries |
|---|---|---|---|
| Kentish Town: terraces with a family bath and a shower | Roadside | Airing cupboard | Family use |
| Kentish Town flats with one shower and two adults | Permit zones | Hall | Light use |
| Kentish Town homes with a lodger or home office | Drives common | Landing | Changing use |
Give the installer your written numbers: who lives in the home, how many baths and showers are taken and when. Ask for the cylinder size and type to be justified in writing.
In a Kentish Town terrace, a household of four plans a new heating system. They write down that two people shower each morning, a child has a bath most evenings and a lodger uses the second bathroom. The installer sizes the cylinder from these numbers and proposes an unvented unit with a quick recovery. The household asks why not a smaller one, and the installer shows how two showers back to back would drain it. They agree on a size with a little room to spare for guests. The cylinder is placed in the airing cupboard, with insulation, a discharge route and a spare shelf left for linen. The household notes the size, type and controls on a card kept with the manuals. A year later, with the lodger gone, they find the size still suits them.
Hot water demand is highest in the winter and during school terms. Choosing a size in early autumn lets the household watch real use before committing. Review the numbers at every change in the household.
A hot water cylinder fed directly from the mains and sealed, with safety devices.
A hot water cylinder fed from a tank in the loft and open to the air through a vent pipe.
How quickly a cylinder reheats its water after some has been used.
From people, bathrooms and how water is used.
No, it takes space and loses heat.
Vented has gentle pressure, unvented has mains pressure.
Yes, ask what happens if the household grows.
Phone 0800 111 999 first; once outside, Kentish Town heating installation yields to the call, and Kentish Town heating installation restarts once cleared.
Talk to Heat Go
Heat Go will draw up a cylinder sizing sheet with spaces for each number on hearing who lives in the home.
The quickest way to talk to a Gas Safe, WaterSafe and G3 certified team is to call +44 7551 336264.
All central heating servicesEvery service in Kentish TownAll central heating installation areas