Cooker & hob installation · Kentish Town

Cooker and hob installation in Kentish Town: swapping a hob for another make and why the cut-out template and the fixing clips rarely match

It is tempting to think that a new hob will drop into the hole left by the old one. In practice, makers differ by a centimetre here or there, and a hob that is a little too wide will not go in. Corner radii, depths and clip positions also vary. A swap that looked simple can end in a worktop cut again. Households in Kentish Town can check the template before the old hob is removed.

Certified for the work. Heat Go holds Gas Safe, WaterSafe, G3 and heating and plumbing certification. Call +44 7551 336264 to talk it through.

Gas Safe Register WaterSafe Heat Go G3 certified Heat Go Heating and Plumbing Engineer

Homes in Kentish Town have worktops of many materials, from laminate and wood to stone, and a hob that has sat in the same hole for years may have left marks. A new hob must fit within the cut-out and also leave the right gap to the wall and the edge. Some worktops cannot be cut without damage.

Five checks help. Measure the existing cut-out, its width, depth and corner radius, and the distance from its edges to the wall and the front. Get the new hob’s template from the maker for cooker and hob installation, and compare it with the measurements, millimetre by millimetre. Check the hob’s depth below the worktop against the unit beneath, since the supply and the cupboard shelf may be in the way. Check the fixing clips or brackets and the thickness of the worktop. And ask the installer to try the template on the worktop with the old hob still in place, if possible. If the new hob is too large, ask whether the cut-out can be enlarged safely or a different hob chosen.

Give Heat Go the two sets of figures, and a comparison table for the old cut-out and the new hob’s template will be set out.

Comparing a new hob’s template with the old cut-out in a Kentish Town kitchen

Cut-out matching questions in Kentish Town kitchens

Kentish Town: kitchens with a laminate worktop

It chips if cut badly. Ask for care and a seal.

Kentish Town homes with a stone worktop

Enlarging a hole is hard. Check the template first.

Kentish Town flats with a hob close to a wall

The gap may be too small. Check the clearance.

SettingParking and van accessProperty accessTypical enquiries
Kentish Town: kitchens with a laminate worktopRoadsideKitchenLaminate tops
Kentish Town homes with a stone worktopPermit zonesKitchenStone tops
Kentish Town flats with a hob close to a wallDrives commonHallTight gaps

Give the installer the old hob’s model and the new hob’s data sheet and template. Show him where the supply comes up under the worktop.

A household in a Kentish Town terrace buys a new four-burner hob to replace an old one of a different make. Before the old hob is removed, the installer compares the template with the cut-out and finds the new hob four millimetres wider. They ask the maker and find a similar model with a matching template. The household changes the order, the new hob drops in with the clips, and the seal is made. The installer connects the gas, tests it and notes the model. The template and the comparison go into the folder. The household files the comparison table and the maker’s template, in case the hob is replaced again. A later buyer’s surveyor reads the model number and the table and sees that the hob was fitted with care. The first order, returned unopened, is a small lesson they repeat to friends.

Hob swaps are often a spring or autumn job. A comparison made before ordering costs nothing and prevents a return. A worktop cut in winter may be harder to repair, with frost affecting adhesives and fillers.

Good to know in Kentish Town

Template

A cutting guide from the maker that shows the exact shape and size of the opening.

Corner radius

The curve at each corner of an opening, which affects how a hob sits.

Fixing clip

A small bracket that holds a hob firmly to the underside of a worktop.

Questions about cooker & hob installation in Kentish Town

01In Kentish Town, will a new hob fit the old hole?

Not always, so compare the template.

02In Kentish Town, what should I measure?

Width, depth, corner radius and distances to the edges.

03In Kentish Town, can a cut-out be enlarged?

Sometimes, depending on the worktop material.

04In Kentish Town, when should I check?

Before the old hob is removed and before ordering.

05cooker and hob installation: gas smelt in Kentish Town?

Ring 0800 111 999 first, and Kentish Town cooker and hob installation comes second, so Kentish Town cooker and hob installation waits until cleared.

Gas emergency

An emergency should not wait for an online enquiry.

If you suspect a gas leak, call the National Gas Emergency Service immediately on 0800 111 999. The enquiry form below is for non-emergency questions.

Talk to Heat Go

Ask about cooker & hob installation in Kentish Town.

Give Heat Go the two sets of measurements, and a comparison table for the swap will be laid out.

The quickest way to talk to a Gas Safe, WaterSafe and G3 certified team is to call +44 7551 336264.

Cooker & hob installation enquiry

What can we help with?

All fields marked * are required

We reply to the contact details you give. A UK number such as 07700 900123 works fine.