Refrigerant-related work · Seven Sisters

Refrigerant-related work in Seven Sisters: why new pipework is evacuated before refrigerant is released and why waiting matters

After the pipework has been proved tight, the next step is to pull the air and moisture out of it with a vacuum pump. Air and damp left inside harm the system and its oil, and can cause faults years later. The step takes time, and it is tempting to hurry it. Residents in Seven Sisters having a unit fitted can ask about the vacuum stage and how it is checked.

Certified for the work. Heat Go holds Gas Safe, WaterSafe, G3 and heating and plumbing certification. Call +44 7551 336264 to talk it through.

Gas Safe Register WaterSafe Heat Go G3 certified Heat Go Heating and Plumbing Engineer

Many flats in Seven Sisters have a short pipe run through a rear wall to a balcony or yard. The work is often fitted into a single visit, and there may be pressure on the fitter to finish. A rushed vacuum leaves moisture behind, which does not show until the unit has run for a while.

There are five points in the stage. The vacuum pump is connected to the pipes and the system, and started. A gauge shows the vacuum falling to a very low pressure, measured in a small unit that the engineer will name. The pump is then isolated, and the gauge is watched to see whether the vacuum holds or rises. A steady reading shows there is no leak and no moisture boiling off. Only then is the refrigerant released from the outdoor unit’s store or topped to the correct amount. Ask the engineer for the vacuum reading, the hold time and the result, and to write them in the record.

Heat Go can draft a few questions about the vacuum stage for the fitter if you tell it the type of unit and the length of the pipe run.

Asking about the vacuum stage before refrigerant is released in a Seven Sisters flat

Vacuum stage questions in Seven Sisters flats

Seven Sisters flats where the unit is fitted in one visit

Time is short. Ask for the vacuum stage not to be hurried.

Seven Sisters flats with a long pipe run through a hall

More pipe holds more air. Ask for a longer vacuum time.

Seven Sisters flats on a damp ground floor

Moisture is a risk. Ask the engineer how the pipes are protected before the test.

SettingParking and van accessProperty accessTypical enquiries
Seven Sisters flats where the unit is fitted in one visitRoadsideBalconySingle visits
Seven Sisters flats with a long pipe run through a hallPermit zonesHallLong runs
Seven Sisters flats on a damp ground floorDrives commonGround floorDamp sites

Show the engineer the pipe route and the unit’s details. Tell him if the pipes have been exposed to rain or damp before the vacuum stage.

A tenant’s landlord has a new unit fitted in a flat, with the pipes run through the rear wall. The engineer connects a vacuum pump after the nitrogen test and shows the tenant the gauge falling to a low reading. He isolates the pump, waits, and shows the gauge holding steady. He writes the reading and the hold time on the record, and only then opens the valves to release the refrigerant. The tenant gets a copy of the record for refrigerant work, and the agent files another with the lease papers.

A fit in spring leaves time to do each stage properly. In a heatwave, the work is rushed because the unit is needed at once. Damp days are the worst for pipes left open, so cover the ends and choose a dry day for the vacuum.

Good to know in Seven Sisters

Vacuum pump

A pump that draws air and moisture out of pipework and a system before it is filled.

Evacuation

The process of pulling a system down to a very low pressure to remove air and moisture.

Isolated

Closed off from other parts of a system so that it can be watched on its own.

Questions about refrigerant-related work in Seven Sisters

01In Seven Sisters, why use a vacuum pump?

To remove air and moisture before the refrigerant goes in.

02In Seven Sisters, how do I know it worked?

The gauge holds steady after the pump is isolated.

03In Seven Sisters, can it be hurried?

It should not be, so ask for the full time.

04In Seven Sisters, should I get the reading?

Ask for it in the record in refrigerant work work in Seven Sisters.

05How does Seven Sisters refrigerant work handle a gas smell?

Ring 0800 111 999 before anything; while Seven Sisters refrigerant work is put aside, and Seven Sisters refrigerant work can restart later.

Talk to Heat Go

Ask about refrigerant-related work in Seven Sisters.

Tell Heat Go your pipe run and the unit type, and a short list of vacuum-stage questions for the fitter will be written.

The quickest way to talk to a Gas Safe, WaterSafe and G3 certified team is to call +44 7551 336264.

Refrigerant-related work enquiry

What can we help with?

All fields marked * are required

We reply to the contact details you give. A UK number such as 07700 900123 works fine.