Thermostats & heating controls · Hornsey

Thermostats and heating controls in Hornsey: the hot water cylinder thermostat, what temperature to set and why it should not be lower

The thermostat on a hot water cylinder decides how hot the stored water becomes. Set it too low, and the water may not be hot enough to protect against bacteria that thrive in warm tanks. Set it too high, and the water can scald at the tap. The usual advice is a setting that keeps the stored water at or above a stated temperature, with a mixing valve at the taps. Households in Hornsey can check the setting in a few minutes.

Certified for the work. Heat Go holds Gas Safe, WaterSafe, G3 and heating and plumbing certification. Call +44 7551 336264 to talk it through.

Gas Safe Register WaterSafe Heat Go G3 certified Heat Go Heating and Plumbing Engineer

Houses in Hornsey often have a copper cylinder in an airing cupboard, with a thermostat strapped to its side and a programmer that sets the times. The thermostat has a dial or a slider with marked temperatures, and its setting may not match the reading of a thermometer. Over the years the dial can drift or the strap can slip. The cylinder’s age and insulation also matter.

To check, find the thermostat and note its setting. Run the hot tap nearest the cylinder after the heating has run, and measure the water with a thermometer in a jug. Compare it with the setting. The stored water should usually be held at around sixty degrees, and kept there for the protection it gives, and a tap temperature lower than that comes from mixing or distance. If the reading is well below the setting, the thermostat or its strap may need attention. Do not lower the setting to save a little; ask the plumber.

Heat Go can interpret the readings. Tell us the setting and the thermometer reading, and a view on what is wrong can be offered.

Checking the hot water cylinder thermostat in a Hornsey house

Cylinder thermostat questions in different Hornsey homes

Houses whose cylinder is an aged copper one

The thermostat may have drifted. Ask the plumber to test it.

Homes with young children living in them

Scalding is a worry. Ask for a mixing valve at the taps, not a lower cylinder setting.

Houses with a cylinder jacket that is worn

Heat escapes and the thermostat works harder. Ask about a new jacket.

SettingParking and van accessProperty accessTypical enquiries
Houses whose cylinder is an aged copper oneRoadsideAiring cupboardDrifted dials
Homes with young children living in themDrives commonBathroomScald risk
Houses with a cylinder jacket that is wornPermit zonesLandingWorn jackets

Give the plumber the setting, the thermometer reading and the age of the cylinder. Tell them about any history of lukewarm water.

A household finds the water lukewarm in the evening. They check the cylinder thermostat and find it set at a middle mark. A jug of water from the nearest tap reads far below sixty. The plumber finds the thermostat’s strap has slipped and fits it properly. He sets the dial to the right mark, and the household’s thermometer now shows a higher reading. He suggests a mixing valve at the bath. The household notes the date and the settings on a card. The plumber adds that a cylinder thermostat is cheap to replace and quick to fit, and that the strap should be checked each year when the heating is serviced. The household adds the check to the service list, and writes the plumber’s name and the date of the repair on the card, beside the thermostat’s make, in case the part needs replacing. The plumber’s invoice, with the date and the part number, goes into the same folder.

A cylinder check is best made in autumn, before the demand for hot water rises, and again each spring.

Good to know in Hornsey

Cylinder thermostat

A sensor on a hot water cylinder that switches the heating off when the water reaches its set temperature.

Strap

The band that holds the thermostat against the side of the cylinder.

Mixing valve

A fitting at the tap that tempers hot water with cold so it cannot scald.

Questions about thermostats & heating controls in Hornsey

01What temperature should the cylinder be?

Usually around sixty degrees, as the plumber advises.

02Why not set it lower?

Water stored too cool may not be protected against bacteria.

03How do I avoid scalding?

With a mixing valve at the taps.

04How do I check the setting?

Measure water from the nearest tap with a thermometer.

05Can the thermostat drift?

Yes, with age or a slipped strap.

Talk to Heat Go

Ask about thermostats & heating controls in Hornsey.

Tell Heat Go the setting and the thermometer reading, naming your Hornsey street, and a view on what is wrong can be offered.

The quickest way to talk to a Gas Safe, WaterSafe and G3 certified team is to call +44 7551 336264.

Thermostats & heating controls enquiry

What can we help with?

All fields marked * are required

We reply to the contact details you give. A UK number such as 07700 900123 works fine.