Thermostats & heating controls · Whetstone

Thermostats and heating controls in Whetstone: two thermostats in one house with underfloor heating and radiators, and how not to let them fight

A house heated by underfloor loops on the ground floor and radiators above has two quite different heating systems on one boiler. Each has its own thermostat, and each responds at its own pace. The floor warms slowly and cools slowly, the radiators quickly. If the two are set against each other, one overheats while the other lags, and the boiler cycles. Households in Whetstone can ask for the controls to be arranged so they cooperate.

Certified for the work. Heat Go holds Gas Safe, WaterSafe, G3 and heating and plumbing certification. Call +44 7551 336264 to talk it through.

Gas Safe Register WaterSafe Heat Go G3 certified Heat Go Heating and Plumbing Engineer

Many houses in Whetstone have been extended, with underfloor heating in the new kitchen and the old radiators left in the rest of the house. The loops run at a lower temperature than the radiators, so a mixing valve and a pump serve them. A room thermostat in the kitchen controls the loops. Another controls the radiator circuit. A single programmer may drive both.

The arrangement should follow five principles. Each zone has its own thermostat in a representative room, away from sun and draughts. Each zone has its own time schedule, since the floor needs a long lead time and the radiators a short one. The boiler receives a call from either zone but supplies the right temperature to each, through the mixing valve. The floor’s sensor limits the surface temperature, protecting timber or stone. And the controls are labelled, so the household knows which does what. Ask for a diagram of the arrangement.

Heat Go can help you check the arrangement. Send the details of the controls, and a few pointers for the installer can be drawn up.

Stopping two thermostats fighting in a Whetstone house with mixed heating

Mixed heating questions in different Whetstone homes

Houses with an underfloor kitchen and radiators upstairs

The kitchen warms slowly. Ask for its schedule to start two hours before use.

Houses with a thermostat in the hall controlling both zones

One reading cannot serve both. Ask for a thermostat in each zone.

Houses with a timber floor over underfloor pipes

Wood limits the surface temperature. Ask for a floor sensor and its set limit.

SettingParking and van accessProperty accessTypical enquiries
Houses with an underfloor kitchen and radiators upstairsRoadsideKitchenSlow floors
Houses with a thermostat in the hall controlling both zonesDrives commonHallwaySingle sensors
Houses with a timber floor over underfloor pipesPermit zonesDining roomTimber floors

Tell the installer which rooms are used when and how long the floor takes to warm. Show them the thermostats and the programmer.

A household in a house with underfloor heating in the kitchen and radiators elsewhere finds the kitchen cold in the morning and the lounge too hot at night. The installer finds a single programmer driving both zones with the same times. He sets the kitchen to start at four and the radiators at six, fits a floor sensor with a safe limit and labels each thermostat. The kitchen is warm by seven. The boiler cycles less, and the household keeps his diagram. The installer adds that the household should avoid setting the kitchen to a high temperature to speed things up, since the floor responds slowly and will overshoot, and suggests they leave it at a steady comfortable level instead. He writes that advice on the diagram, beside the times. The installer also explains that the floor sensor’s limit should be left alone unless the floor covering changes, and writes the limit and the date on the diagram. When the household later replaces the tiles with timber, they ring to ask whether the limit should be lowered. He confirms it should, and revises the diagram, adding the date and the new tile’s thickness, and the household files both versions.

Controls are best reviewed before the heating season, so a visit in early autumn finds conflicts before the cold arrives.

Good to know in Whetstone

Mixing valve

A valve that blends hot and cooler water to give underfloor loops a lower temperature than the radiators.

Floor sensor

A sensor that measures the floor surface temperature and stops it exceeding a set limit.

Lead time

The time a heating system needs to bring a room to temperature before it is used.

Questions about thermostats & heating controls in Whetstone

01Why do the zones fight?

They respond at different speeds and may be set to the same times.

02How long does underfloor heating take to warm?

Often a few hours, longer than radiators.

03Does a floor need a sensor?

Often, to protect timber and stone.

04Can one programmer run both zones?

Yes, with separate schedules for each.

05Should the thermostats be labelled?

Yes, so everyone knows which controls what.

Talk to Heat Go

Ask about thermostats & heating controls in Whetstone.

Give Heat Go the details of your controls along with your Whetstone address, and a few pointers for the installer can be drawn up.

The quickest way to talk to a Gas Safe, WaterSafe and G3 certified team is to call +44 7551 336264.

Thermostats & heating controls enquiry

What can we help with?

All fields marked * are required

We reply to the contact details you give. A UK number such as 07700 900123 works fine.