Thermostats & heating controls · Camden Town

Thermostats and heating controls in Camden Town: a plain map of which control does what, from the programmer to the cylinder thermostat

A heating system has several controls, each with a limited job, and they work together only if each does its part. The programmer sets the times, the room thermostat decides when it is warm enough, the cylinder thermostat looks after hot water, and the radiator valves tune each room. When one is set wrongly, the fault can look like a boiler problem. Households in Camden Town can draw a simple map.

Certified for the work. Heat Go holds Gas Safe, WaterSafe, G3 and heating and plumbing certification. Call +44 7551 336264 to talk it through.

Gas Safe Register WaterSafe Heat Go G3 certified Heat Go Heating and Plumbing Engineer

Camden Town’s flats and terraces often have controls fitted at different times: a modern thermostat on the wall, an old cylinder thermostat strapped to a pipe, and radiator valves of mixed types. Few residents know how they link.

A programmer is the timer that sets the periods when heating and hot water are permitted to run. The room thermostat senses the air at its own spot on the wall and signals the boiler to heat or pause. The cylinder thermostat measures the temperature of the hot water and shuts off the heating of the cylinder when it is hot enough. In many systems, a motorised valve directs hot water to either the radiators or the cylinder. The radiator valves adjust the flow to each room. Draw a box for each control and an arrow for what it tells. Mark where each is located and what it is set to. Check that the room thermostat is not in a draught or in the sun, and that the cylinder thermostat is set high enough to keep the water hot, as the guide advises. Ask the engineer to check the map and correct it. Keep it with the guide.

A controls map page, with a box for each control, a place for its position and setting and arrows for what it tells: ready from Heat Go after you share with Heat Go what controls you have.

Drawing a map of what each heating control does in a Camden Town home

Heating controls map questions in Camden Town

Camden Town flats with controls fitted at different times

Links are unclear. Draw a map.

Camden Town homes with a cylinder thermostat strapped on

Its setting matters. Ask the engineer.

Camden Town: households where the heating comes on at odd times

The programmer may be the cause. Check it.

SettingParking and van accessProperty accessTypical enquiries
Camden Town flats with controls fitted at different timesRoadsideHallMixed controls
Camden Town homes with a cylinder thermostat strapped onPermit zonesAiring cupboardCylinder stats
Camden Town: households where the heating comes on at odd timesDrives commonKitchenOdd timings

Show the engineer your map and ask them to correct it. Tell them if the heating or hot water behaves oddly and which control you suspect.

In a Camden Town flat, a household finds that the hot water runs out in the morning though the timer seems right. They draw a map of the controls and find that the cylinder thermostat is set low. They mark each control’s position: the programmer in the hall, the room thermostat on the living room wall, the cylinder thermostat in the airing cupboard. The engineer corrects the map, explaining that the motorised valve sends water either to the radiators or to the cylinder. He raises the cylinder thermostat to the setting in the guide. The hot water now lasts through the morning. The household notes the setting on the map and files it with the guide. A visitor later uses the map to understand the system, and sets the programmer with ease.

A controls map is most helpful when the heating season begins, and again whenever a control is replaced. Update it whenever a setting or a part changes.

Good to know in Camden Town

Programmer

A clock that chooses the moments when the heating and the water heating start and stop.

Cylinder thermostat

A device that senses the temperature of the hot water cylinder and shuts off heating to it when it is hot enough.

Motorised valve

A valve operated by a small motor that directs hot water to the radiators or the cylinder.

Questions about thermostats & heating controls in Camden Town

01In Camden Town, which control sets the times?

The programmer.

02In Camden Town, which control decides when it is warm enough?

The room thermostat.

03In Camden Town, what does the cylinder thermostat do?

It keeps the hot water at its set temperature.

04In Camden Town, why draw a map?

So faults can be traced to the right control.

05How does Camden Town heating controls handle a gas smell?

First, 0800 111 999 is rung; meanwhile Camden Town heating controls is put aside, and Camden Town heating controls restarts when cleared.

Talk to Heat Go

Ask about thermostats & heating controls in Camden Town.

Tell Heat Go which controls you have, and a controls map page with a box for each will be laid out.

The quickest way to talk to a Gas Safe, WaterSafe and G3 certified team is to call +44 7551 336264.

Thermostats & heating controls enquiry

What can we help with?

All fields marked * are required

We reply to the contact details you give. A UK number such as 07700 900123 works fine.