Houses with radiators on three floors
Air rises. Start on the ground floor and finish at the top.
Heat pump maintenance · Golders Green
Radiators on a heat pump system sometimes hold air, particularly in the first winter or after repairs. Bleeding them is a simple task, but the circuit is sealed and holds water at a set pressure. Letting out air lets the pressure fall, and the system may need topping up. A householder who does it carefully can keep the radiators warm, and one who does it carelessly can trip an alarm. Households in Golders Green can learn the safe way.
Certified for the work. Heat Go holds Gas Safe, WaterSafe, G3 and heating and plumbing certification. Call +44 7551 336264 to talk it through.
Larger houses in Golders Green have many radiators and long runs, so air collects in places. A radiator that feels cool at the top and warm at the bottom is likely to hold air. The heat pump’s circuit works at modest temperatures, and trapped air shows as cold spots and noise. The pressure gauge, near the cylinder or the pump, shows the reading before and after.
A careful bleed has six steps. Read the pressure gauge and note it. Switch the heating off and let the radiators cool. Bleed with a key and a cloth, starting at the lowest radiator and working up. Close the valve as soon as water, not air, appears. Read the gauge again, and top up to the recommended pressure by the method the installer showed. And switch the heating back on, and check each radiator once it has warmed. If the pressure falls repeatedly after bleeding, ask for a check.
Heat Go can plan a bleed with you. Say how many radiators the house has and where the gauge sits, and a step-by-step list can be drafted.
Air rises. Start on the ground floor and finish at the top.
Loops are bled at the manifold, not with a key. Ask the engineer to show you or do it.
Access is awkward. Ask whether the gauge can be moved or a spare fitted lower.
| Setting | Parking and van access | Property access | Typical enquiries |
|---|---|---|---|
| Houses with radiators on three floors | Roadside | Landing | Multi-floor systems |
| Houses with underfloor loops on the ground floor | Drives common | Utility room | Underfloor loops |
| Houses with a pressure gauge in the loft | Permit zones | Loft hatch | Remote gauges |
Tell the engineer which radiators were bled, the pressure before and after and the date. Ask them to look at the filling method if you are unsure.
A household notices a radiator in the study stays cool at the top. They read the gauge, which stands at one and a half, switch off and let the system cool. They bleed the radiator and a short hiss gives way to water. The gauge reads slightly lower, so they top up by the method the installer showed. The radiator warms through, and the household writes both readings in a notebook. They then tell their neighbour, who has a similar system, how the process went, and she tries it herself. The engineer, at the next service, checks the gauge and the filling method and confirms the household has done it correctly. He adds a note on the sheet that radiators were bled in October and the pressure restored to the right figure, so that the record shows the work.
Bleeding is best done in autumn, before the heating season, and again if a radiator is cool after repairs.
A small key that turns the screw at the top of a radiator so trapped air can escape.
A flexible pipe, fitted with a valve at both ends, used to add water to the sealed circuit.
A distribution block that splits the water into separate circuits, such as underfloor loops.
Yes, with a key and a cloth, following the steps carefully.
Air has left the system and the circuit needs topping up.
By the method the installer showed, to the recommended pressure.
Report it, since a leak may be present.
When a radiator is cool at the top, and in autumn.
Talk to Heat Go
Give Heat Go the number of radiators and the gauge’s position, along with your Golders Green road, and a step-by-step list can be drafted.
The quickest way to talk to a Gas Safe, WaterSafe and G3 certified team is to call +44 7551 336264.
All heat pumps servicesEvery service in Golders GreenAll heat pump maintenance areas