Heat pump repairs · Edgware

Heat pump repairs in Edgware: the electric immersion heater keeps switching in and the bills rise

A heat pump heats the hot water cylinder, and an electric immersion heater inside it acts as a back-up. Used rarely, it is a safety net. If it switches in often, the electricity used climbs and the household notices. The cause may be a setting, a fault or a pump struggling to reach temperature. Households in Edgware can look at the signs, and ask for the cause to be found.

Certified for the work. Heat Go holds Gas Safe, WaterSafe, G3 and heating and plumbing certification. Call +44 7551 336264 to talk it through.

Gas Safe Register WaterSafe Heat Go G3 certified Heat Go Heating and Plumbing Engineer

Cylinders in Edgware homes with heat pumps usually have a thermostat and a heater controlled by the system. The heater switches in when the pump cannot reach the target temperature, or when the controller calls for a legionella cycle, or when a boost is requested. If the pump has a fault, or the target is set very high, the heater may run daily.

Look at five things. The electricity use on the meter or the app, and any rise since the system was installed. The cylinder temperature setting and the schedule on the controller. Whether a boost or legionella cycle is set often. Any alarm or fault code on the heat pump. And the hot water behaviour: does it run hot early and cool later? Write down what the controller shows when the heater is on. If it seems to run daily, report it, with the readings.

Heat Go can look into it with you. Send the readings and the controller’s settings, and a view on what may be behind it can be offered.

Checking why the immersion heater runs on a heat pump cylinder in Edgware

Immersion heater questions in different Edgware homes

Homes with a large family and heavy hot water use

The pump may struggle to keep up. Ask whether the cylinder is the right size.

Homes with the target set very high

A high setting forces the heater to help. Ask whether a lower one would do.

Homes with a pump that has a fault

A fault may stop the pump heating the water. Check for a code and report it.

SettingParking and van accessProperty accessTypical enquiries
Homes with a large family and heavy hot water useRoadsideAiring cupboardHeavy use
Homes with the target set very highDrives commonUtility roomHigh targets
Homes with a pump that has a faultPermit zonesHallFault codes

Give the engineer the controller’s settings, the pattern of hot water use and the rise in electricity use, and mention any alarm.

A household notices the electricity bill rises after installing the heat pump. They look at the controller and find the immersion heater runs every evening. The engineer finds the cylinder target is set at the maximum, and the pump cannot reach it in cold weather. He lowers it and adjusts the schedule. The immersion heater runs only for the weekly cycle. The next month’s use falls, and they note the settings. The engineer also suggests that a smaller, more frequent heating of the cylinder is usually better than a hot, rare one, and explains how to set the schedule to match the household’s peak use in the morning and evening. The household notes the times on a card pinned inside the cupboard door, and adds the bills for the next three months to the folder, so that the effect can be compared over the whole winter. They also ask the engineer for his view on whether the cylinder is the right size for a household of their number, and he promises to report back in writing. He later confirms that the cylinder is adequately sized, and that the rise in use came from the setting alone.

A check of the hot water settings is best made in autumn, before cold weather makes the pump work hardest.

Good to know in Edgware

Immersion heater

An electric element inside the cylinder that can heat the water directly.

Legionella cycle

A periodic heating of the cylinder to a higher temperature to protect the water.

Target temperature

The temperature the controller tries to reach and hold in the cylinder.

Questions about heat pump repairs in Edgware

01Why does the immersion heater come on?

The pump may not reach the target, or a boost or cycle is called for.

02Does it matter?

Yes, because electric heating costs more than the pump’s.

03Can I turn it off?

Not without advice, since it protects against legionella and cold weather.

04How do I see it on the controller?

The display shows when it is on. Photograph it.

05Is a lower target worth trying?

Often, with the engineer’s advice.

Talk to Heat Go

Ask about heat pump repairs in Edgware.

Send Heat Go the settings and readings for your Edgware home, and a view on what may be behind the heater can follow.

The quickest way to talk to a Gas Safe, WaterSafe and G3 certified team is to call +44 7551 336264.

Heat pump repairs enquiry

What can we help with?

All fields marked * are required

We reply to the contact details you give. A UK number such as 07700 900123 works fine.