Cooker & hob installation · Hendon

Cooker and hob installation in Hendon: measuring the worktop cut-out before the new hob is ordered

Replacing a built-in hob sounds like a simple swap, until the new one is a centimetre too wide for the hole. The cut-out in the worktop was made for the old hob, and the new one must fit it, with room to spare underneath for the pipes, cables and clearances. A few minutes with a tape measure before ordering avoids a delivery that cannot be fitted. Residents in Hendon can do this themselves and give the installer the figures.

Certified for the work. Heat Go holds Gas Safe, WaterSafe, G3 and heating and plumbing certification. Call +44 7551 336264 to talk it through.

Gas Safe Register WaterSafe Heat Go G3 certified Heat Go Heating and Plumbing Engineer

Flats near Hendon Central often have worktops of laminate or timber, fitted some years ago, with a cut-out of a standard size for the hob of the day. Newer hobs come in different widths and depths, and some need a deeper space underneath for their controls and burners. The worktop may also be thin, or boxed over a cupboard that limits the depth available. A hob that is too deep or too wide cannot be forced in.

The measuring is straightforward. Measure the width and depth of the cut-out at its widest and narrowest points, in millimetres. Measure the distance from the cut-out to the back wall and to the nearest cupboard, since clearances apply. Check the thickness of the worktop. Look under the hob for what sits there: pipes, wiring, the cupboard shelf. Then compare these figures with the installation sheet of the hob you have in mind, which gives the cut-out and the clearance underneath. If they do not match, the worktop may need altering, which is a job for a joiner.

Heat Go can help you check a hob against a cut-out. Send the measurements and a photograph of the worktop, and a list of points to compare can be drawn up.

Measuring for a replacement hob in a Hendon kitchen

Hob fitting questions in different Hendon kitchens

Flats with a laminate worktop

A laminate edge can chip if the cut-out is enlarged. Ask whether the existing hole can be used as it is.

Flats with a worktop over a shallow cupboard

Limited depth below may rule out a deep hob. Check the installation sheet for the clearance.

Flats where the hob is near a window or wall

Clearances to walls and curtains apply. Ask the installer to measure them against the sheet.

SettingParking and van accessProperty accessTypical enquiries
Flats with a laminate worktopPermit zonesKitchenEdge damage
Flats with a worktop over a shallow cupboardRoadsideGalley kitchenShallow cupboards
Flats where the hob is near a window or wallDrives commonKitchen windowNearby surfaces

Tell the installer what the old hob was, what you want to fit and what the measurements are. Photographs of the underside are helpful.

A resident wants to replace a four-ring hob with a newer one. She measures the cut-out and finds it two centimetres narrower than the model she had in mind. She picks another with a smaller footprint that matches the sheet. The installer checks the clearances, fits the hob, connects it and tests it. The new hob sits flush, with no gaps, and the worktop edge is undamaged. She keeps the installation sheet with the receipt and writes the measurements of the cut-out on its first page, so that the next owner, or the next hob, can be matched in a minute. The installer adds that the sealant strip along the edge should be checked each year, since a gap there lets spills run into the cupboard below, and the resident puts it on her September list.

Measuring costs nothing and is best done before ordering. A refit planned in September, with the hob delivered in good time, leaves the kitchen ready before the busy winter months.

Good to know in Hendon

Cut-out

The opening in a worktop into which a built-in hob is set.

Clearance

The free space required between a hob and the wall, cupboards or other surfaces.

Installation sheet

The maker’s drawing that gives the cut-out size and the clearances for a hob.

Questions about cooker & hob installation in Hendon

01Will any hob fit my cut-out?

Only one whose sheet matches your measurements.

02Can the cut-out be enlarged?

Often, by a joiner, but the edge and the worktop must be sound.

03What if gas is smelt after a hob is fitted?

Turn the hob off, air the room, leave the house and dial 0800 111 999.

04Do clearances really matter?

Yes. They protect walls and units from heat.

05Who should fit it?

A competent installer, with the connection tested.

Gas emergency

An emergency should not wait for an online enquiry.

If you suspect a gas leak, call the National Gas Emergency Service immediately on 0800 111 999. The enquiry form below is for non-emergency questions.

Talk to Heat Go

Ask about cooker & hob installation in Hendon.

Send Heat Go the measurements of your cut-out and your Hendon street, and points to compare with the hob’s sheet can be drawn up.

The quickest way to talk to a Gas Safe, WaterSafe and G3 certified team is to call +44 7551 336264.

Cooker & hob installation enquiry

What can we help with?

All fields marked * are required

We reply to the contact details you give. A UK number such as 07700 900123 works fine.