Cooker & hob installation · Whetstone

Cooker and hob installation in Whetstone: measuring a kitchen for a new hob so the cut-out, the distances and the supply all fit

A hob that does not fit its worktop is an expensive mistake. The cut-out is a few millimetres too small, the gas pipe is on the wrong side or a wall unit is too close. A tape measure and a few minutes at home before ordering avoids all of it. Households in Whetstone can measure first and share the numbers.

Certified for the work. Heat Go holds Gas Safe, WaterSafe, G3 and heating and plumbing certification. Call +44 7551 336264 to talk it through.

Gas Safe Register WaterSafe Heat Go G3 certified Heat Go Heating and Plumbing Engineer

Houses in Whetstone have kitchens of many sizes, from small galley rooms to large extensions. Worktop depth, the position of drawers below and the height of units above all affect where a hob can go. The gas pipe may need to move.

Six measurements cover the job. First, the width and depth of the opening cut in the worktop, or the space for a freestanding cooker. The distance from the hob edge to the back wall and to any side wall. The height of units or an extractor above, and the maker’s minimum. The position and height of the gas pipe and whether it can reach. The depth of the unit below and whether a drawer will clash with the hob’s underside. And the position of the electricity supply for ignition. Write each on a sketch and photograph the area. Share them with the installer before the hob is bought.

Heat Go can help you measure up. Say what you plan, and a sketch sheet showing each measurement to take can be drawn up.

Measuring a kitchen for a new gas hob in a Whetstone house

Hob fitting questions in different Whetstone homes

Houses getting a new worktop

The cut-out is new. Order the hob first and measure from its template.

Houses swapping an old hob for a new one

The old cut-out may differ. Measure it before buying.

Houses replacing a freestanding cooker

Width and gas hose position matter. Check both.

SettingParking and van accessProperty accessTypical enquiries
Houses getting a new worktopRoadsideKitchenNew worktops
Houses swapping an old hob for a new oneDrives commonKitchenReplacements
Houses replacing a freestanding cookerPermit zonesUtility roomCooker swaps

Give the installer the sketch and photographs, and tell them the make and model of the hob you have in mind. Say whether the worktop is stone, wood or laminate, since each is cut differently and the installer may need to ask for a specialist, and say who will do the cutting.

A Whetstone household plans to replace an old hob. They measure the cut-out, note the gap to the wall and the height of the extractor above, and see that the gas pipe comes through the back wall on the left. They photograph the lot and send the sketch to the installer. He says the new hob needs a slightly larger cut-out and that the pipe needs to move. They order the hob with the right template and book the work. On the day, the installer checks the cut-out against the template, trims a few millimetres from the worktop edge with a fine blade, moves the pipe, fits the hob and tests the connection. The household had also remembered to measure the depth under the hob, and the drawer below, which would have hit the underside, is swapped for a shallower one beforehand. The installer shows how each burner lights and leaves the manual with them, and explains what a yellow tip on a flame would mean. A photograph of the pipe before it was covered goes in the kitchen folder.

Measuring in late summer leaves time to order the hob and any worktop work before busy periods arrive. A hob that arrives in a week and finds the pipe in the wrong place can sit in its box for a month, while an installer is found, and a household that measures first avoids both the wait and the disappointment.

Good to know in Whetstone

Cut-out

The hole cut in a counter so that a hob can drop in.

Template

A paper or card pattern from the maker that shows the exact size of a cut-out.

Clearance

The space the maker requires between a hob and walls, units or an extractor.

Questions about cooker & hob installation in Whetstone

01Which measurements come first?

The cut-out, the distances to walls and the height of units above.

02Why is the pipe position important?

It may need to move to reach the new hob.

03Does the hob come first or the measuring?

Choose the hob first, then check the cut-out against its template.

04Is self-fitting possible?

No. A gas hob needs a proper connection by an engineer.

05What if the new hob gives off a gas smell?

The house should be left straight away and 0800 111 999 called from outside. No switch, no flame, and no waiting for the installer.

Gas emergency

An emergency should not wait for an online enquiry.

If you suspect a gas leak, call the National Gas Emergency Service immediately on 0800 111 999. The enquiry form below is for non-emergency questions.

Talk to Heat Go

Ask about cooker & hob installation in Whetstone.

Tell Heat Go what hob you plan for your Whetstone kitchen, and a sketch sheet of measurements can be drawn up.

The quickest way to talk to a Gas Safe, WaterSafe and G3 certified team is to call +44 7551 336264.

Cooker & hob installation enquiry

What can we help with?

All fields marked * are required

We reply to the contact details you give. A UK number such as 07700 900123 works fine.