Central heating installation · Mill Hill

Central heating installation in Mill Hill: replacing a loft tank and cylinder system with a sealed one

Many older heating systems depend on tanks in the loft: a small feed-and-expansion tank for the heating and a larger cold water tank for the cylinder. A modern installation often removes them and uses a sealed circuit. The change frees loft space, but it also changes how the system behaves, and the existing pipes and radiators must cope. Households in Mill Hill can ask what will be removed, what will be reused and why.

Certified for the work. Heat Go holds Gas Safe, WaterSafe, G3 and heating and plumbing certification. Call +44 7551 336264 to talk it through.

Gas Safe Register WaterSafe Heat Go G3 certified Heat Go Heating and Plumbing Engineer

Lofts across Mill Hill, near either of its two stations, often hold a tank or two, with a cylinder in an airing cupboard below. Replacing the system may mean draining the tanks, capping redundant pipes and re-routing the vent pipe. The pipes in the loft must be insulated where they remain, and any pipe left in the loft should be checked for frost risk.

Four steps cover the change. The installer inspects the existing pipes, cylinder and radiators, and says what can be reused. The old tanks and redundant pipes are drained and removed. The new sealed circuit is filled, pressurised and tested, with a filling loop and an expansion vessel. And the cylinder, if kept, is checked for compatibility with the new controls. Ask for a note of what was removed, what was kept and the pressure the system should run at.

Heat Go can help you list questions about a sealed system. Send photographs of the loft tanks, the cylinder and the pipes, and a few points for the installer can follow.

Questions about replacing loft tanks with a sealed system in Mill Hill

Sealed system questions in different Mill Hill homes

Houses with a large loft and two tanks

The tanks and old pipes are removed. Ask how the loft will be left and whether any frost risk remains.

Houses with an old cylinder in the airing cupboard

An old cylinder may need replacing. Ask whether it suits the new system and its controls.

Houses with original radiators and pipework

Old radiators may be fine, but the water may be dirty. Ask about cleaning or flushing before the new boiler is connected.

SettingParking and van accessProperty accessTypical enquiries
Houses with a large loft and two tanksDrives commonLoft hatchTank removal
Houses with an old cylinder in the airing cupboardRoadsideLandingCylinder condition
Houses with original radiators and pipeworkPermit zonesHallwayReuse of radiators

Tell the installer how the loft is reached and whether it is boarded. Show them the tanks and the cylinder before the quote is written.

A household replaces a gravity-fed system. The installer inspects the tanks, the cylinder and the radiators, drains the system and removes the loft tanks. The pipes are capped and the loft is tidied, with the remaining pipes insulated. The new circuit is sealed, filled and pressurised. The installer explains where the filling loop is and what pressure to expect, and leaves a note for the household. A month later the household checks the pressure gauge, finds it where the note says it should be and has no need to call anybody. The empty space in the loft is used for storage, with the remaining insulated pipes clearly marked so that nothing is stacked against them. The installer also notes which radiators were reused and which were new, so that the household knows what to watch in the first season. If a reused radiator shows cold patches, it can be bled or flushed without disturbing the rest of the circuit.

Removing loft tanks is best done in dry weather, when the loft is easy to reach and the heating can be off for a few days. September suits well.

Good to know in Mill Hill

Sealed system

A heating circuit that is filled under pressure and closed to the air, with no loft tank.

Expansion vessel

A small vessel that takes up the water’s expansion as it heats up.

Filling loop

A flexible connection used to top up the pressure in a sealed system.

Questions about central heating installation in Mill Hill

01Why replace loft tanks?

A sealed system needs none and frees loft space, though it must be installed properly.

02Can old radiators be reused?

Often, if they are sound. The installer will check them.

03Will the cylinder need replacing?

Possibly. It depends on its age and the new controls.

04How do I top up a sealed system?

With the filling loop, following the installer’s note.

05What pressure should it run at?

The installer will state it. Keep the note.

Talk to Heat Go

Ask about central heating installation in Mill Hill.

Send Heat Go photographs of your loft and cylinder with your Mill Hill road, and questions for the installer can be listed.

The quickest way to talk to a Gas Safe, WaterSafe and G3 certified team is to call +44 7551 336264.

Central heating installation enquiry

What can we help with?

All fields marked * are required

We reply to the contact details you give. A UK number such as 07700 900123 works fine.