Kitchens where the gas pipe is behind the old cooker
The pipe may need extending to the hob position. Say how far the new hob will be.
Gas appliance installation · Barnet
A freestanding cooker plugs in and slides out, while a built-in hob and oven are separate units fitted into worktops and tall units. The change gives a smarter kitchen, but it moves the gas connection, adds an electrical supply for the oven and requires a cut-out in the worktop. Getting each piece right before the kitchen fitter arrives avoids delays. Households in Barnet planning the swap can follow the steps below.
Certified for the work. Heat Go holds Gas Safe, WaterSafe, G3 and heating and plumbing certification. Call +44 7551 336264 to talk it through.
Many homes around Chipping Barnet have kitchens that have been refitted more than once, with the gas pipe for the cooker sitting wherever the first owner put it. The pipes behind the units are often older than the units themselves. A new hob may need the gas supply re-routed, and the old supply capped.
The sequence runs as follows. The kitchen fitter prepares the worktop and tall unit. A gas engineer re-routes or extends the gas pipe to the hob position, fits an isolation valve in an accessible place and connects the hob with an approved flexible connector. An electrician supplies the oven. The gas connection is tested for soundness and the hob is lit and adjusted so that each burner burns steadily. The oven is checked and the household is shown how everything works. The order matters, since the gas pipe must be in place before the worktop is sealed, and a pipe that has to be added afterwards means cutting into a brand-new worktop or unit.
How the gas side of a cooker swap fits with the kitchen fitter’s schedule is worth settling early. Tell Heat Go when the kitchen is being fitted and which appliances you have chosen, and the sequence can be set out.
The pipe may need extending to the hob position. Say how far the new hob will be.
An island hob needs a supply under the floor. Check the floor and the route in good time.
Space for the valve and hose is tight. Photograph the cupboard below the hob.
| Setting | Parking and van access | Property access | Typical enquiries |
|---|---|---|---|
| Kitchens where the gas pipe is behind the old cooker | Roadside | Kitchen | Pipe extensions |
| Kitchens with a new island | Drives common | Kitchen island | Floor routes |
| Flats with a compact kitchen | Permit zones | Compact kitchen | Tight cupboards |
Explain the route to the kitchen and when the kitchen fitter will be present. The gas connection must be made at the right moment in the sequence.
A couple fit a new kitchen with a built-in hob. The kitchen fitter asks when the gas engineer will come, and they realise that the pipe must be moved before the worktop goes down. They send the hob’s instructions and a photograph of the old pipe to Heat Go, and learn that the gas connection should be planned for the day before the worktop is fixed.
Kitchen projects often finish in the autumn, ahead of the holidays. A gas connection planned in September, with the fitter’s dates in hand, avoids a rush in December.
A valve that shuts off gas to the hob. It must be accessible, not hidden behind the unit.
An approved hose that connects the hob to the gas pipe. It must suit the appliance and be correctly fitted.
The opening in the worktop for the hob. It must match the hob’s dimensions.
Gas work is for a gas engineer. Do not attempt it, and do not let the kitchen fitter connect the gas.
Many built-in ovens are electric, so check the model, and if an electric oven is chosen, an electrician must supply it.
In an accessible place, usually in the cupboard below the hob, where a hand can reach it without moving anything heavy.
Often. The hob position decides, and the old connection must be capped safely once the cooker has gone.
Before the worktop is fixed, so the pipe can be routed, and again after the hob is in place to connect and test it.
Gas emergency
If you suspect a gas leak, call the National Gas Emergency Service immediately on 0800 111 999. The enquiry form below is for non-emergency questions.
Talk to Heat Go
The sequence of work can be set out once Heat Go has the appliances, the kitchen layout and the name of your Barnet road. Gas in the air has its own free number, 0800 111 999, which must be used instead of any enquiry.
The quickest way to talk to a Gas Safe, WaterSafe and G3 certified team is to call +44 7551 336264.
All gas servicesEvery service in BarnetAll gas appliance installation areas