Gas appliance installation · Mill Hill

Gas appliance installation in Mill Hill: moving a gas cooker during a kitchen refit and what the new connection needs

A kitchen refit often moves the cooker, and moving a gas cooker is more than sliding it along. The supply point must move too, or the hose must reach. The connection must be of the right type for the appliance, and the cooker must be held steady so that it cannot be pulled and strain the gas connection. Households in Mill Hill can ask the installer how each point will be handled, and ask for the work to be tested.

Certified for the work. Heat Go holds Gas Safe, WaterSafe, G3 and heating and plumbing certification. Call +44 7551 336264 to talk it through.

Gas Safe Register WaterSafe Heat Go G3 certified Heat Go Heating and Plumbing Engineer

Kitchens in older Mill Hill houses often have the gas supply at a single point behind where the cooker used to stand. A new layout may place the cooker a metre or two away. The simplest answer is a new pipe to the new spot, with a fixed connection and a valve. A longer flexible hose is not a good substitute, because hoses have limits on length and position.

Five points make a good result. A new supply point close to the cooker, with a valve in reach. A connection of the right type, a bayonet fitting with a suitable hose or a fixed pipe where the appliance allows. A restraint, such as a chain, if the cooker can move on its own wheels or when pulled. A safe clearance from nearby units and surfaces, in line with the appliance’s instructions. And a test of the connection for soundness, followed by lighting every burner and the oven.

Heat Go can note what needs settling for a cooker move. Send the new layout with the cooker marked, and a few queries for the installer can be written down.

Planning a gas cooker move in a Mill Hill kitchen refit

Cooker move questions in different Mill Hill homes

Houses where the cooker moves along the same wall

The distance may be short but the pipe must still be extended. Ask whether the old stub will be capped safely.

Houses where the cooker moves to another wall

A longer pipe run follows. Ask how it will be routed and shielded beneath units or floors.

Houses with a range cooker replacing a standard one

A range is wider and heavier. Ask about the clearance, the restraint and the supply position.

SettingParking and van accessProperty accessTypical enquiries
Houses where the cooker moves along the same wallDrives commonKitchenShort moves
Houses where the cooker moves to another wallRoadsideUtility areaNew walls
Houses with a range cooker replacing a standard onePermit zonesBack kitchenLarger cookers

Tell the installer the cooker’s make and model and show them the new layout. Say when the units go in.

A household refits a kitchen and moves the cooker two metres along the wall. The installer extends the pipe from the old supply, fits a valve behind the plinth and caps the old stub safely. A flexible hose of the right length is connected with a restraint chain. After the connection is tested for soundness, each burner and the oven are lit and checked. The household files the note of the work. They also ask the installer to show them where the old stub is capped, and to mark the position on the plan, so that anyone who works behind the units later knows what is there. The installer adds that a cooker should be pushed back only as far as the restraint allows, and the household sticks a reminder inside the cupboard door, with the date of the work written beside it.

A cooker move is best made when the units are fitted, so that the pipe route is fresh. A refit in September leaves the household with a cooker before the winter.

Good to know in Mill Hill

Bayonet fitting

A quick-release gas connector used with a flexible hose on some cookers.

Restraint

A chain or bracket that stops a cooker being pulled forward and straining its gas connection.

Cap

A fitting that closes the end of a gas pipe that is no longer used.

Questions about gas appliance installation in Mill Hill

01Can I move my own cooker?

No. The gas connection is for a competent installer.

02Do I need a new pipe?

Often, if the new position is some distance from the old supply.

03What is a restraint?

A chain that stops the cooker moving and straining the connection.

04What if gas is noticed after the move?

Shut the valve if safe, open a window, then get out and put 0800 111 999 ahead of every other call.

05Is a test needed?

Yes, before the cooker is used.

Gas emergency

An emergency should not wait for an online enquiry.

If you suspect a gas leak, call the National Gas Emergency Service immediately on 0800 111 999. The enquiry form below is for non-emergency questions.

Talk to Heat Go

Ask about gas appliance installation in Mill Hill.

Send Heat Go the new kitchen layout and your Mill Hill road, and points for the installer can be listed.

The quickest way to talk to a Gas Safe, WaterSafe and G3 certified team is to call +44 7551 336264.

Gas appliance installation enquiry

What can we help with?

All fields marked * are required

We reply to the contact details you give. A UK number such as 07700 900123 works fine.