Heat pump controls & optimisation · Hendon

Heat pump controls in Hendon: setting the hot water schedule and the weekly high-temperature cycle

The cylinder on a heat pump system is heated on a schedule, and the schedule is one of the easiest controls to improve. Heat the water at the wrong time and you either run out or waste effort. There is also a weekly cycle, which raises the cylinder to a higher temperature briefly to protect the water, and it is best timed to suit the household. Residents in Hendon can set both in minutes and note the result.

Certified for the work. Heat Go holds Gas Safe, WaterSafe, G3 and heating and plumbing certification. Call +44 7551 336264 to talk it through.

Gas Safe Register WaterSafe Heat Go G3 certified Heat Go Heating and Plumbing Engineer

In Hendon, a heat pump home keeps its cylinder in a cupboard, a controller on the wall and a default schedule from installation. The default rarely fits the household’s day. A cylinder holds hot water for many hours, so it can be heated at a time when the pump works well, and need not be heated twice. The weekly cycle runs on its own unless told otherwise.

Setting the schedule takes four steps. List when the household needs hot water: showers in the morning, baths in the evening, washing up after meals. Choose one or two heating periods that finish shortly before the busiest use, often early morning and mid-afternoon. Choose a cylinder temperature that is hot enough but not higher than needed. And set the weekly higher-temperature cycle for a time when hot water is not in demand, such as a weekday afternoon. Note the settings and check after a week whether the hot water ran short.

Heat Go can work out a schedule with you. Tell us how the household uses hot water, and starting times can be proposed.

Choosing hot water heating times for a Hendon heat pump

Hot water schedule questions in different Hendon buildings

Flats with a working household out all day

Heat once, early, and again mid-afternoon if needed. Avoid heating during the working hours when no one is home.

Homes with a family and morning showers

The cylinder must be ready by seven. Set the heating to finish before then.

Homes where someone works at home

Hot water is needed through the day. A mid-day top-up may suit.

SettingParking and van accessProperty accessTypical enquiries
Flats with a working household out all dayPermit zonesBathroomDaytime absence
Homes with a family and morning showersRoadsideAiring cupboardMorning peaks
Homes where someone works at homeDrives commonStudyAll-day use

Tell the engineer how the household uses hot water and which days are heaviest. Ask them to set the weekly cycle for a quiet time.

A household has a heat pump and finds the hot water runs short on Monday mornings. They look at the schedule and find the heating finishes at six, but the weekly high-temperature cycle runs on Monday at five, and uses up the heat. They move the cycle to Wednesday afternoon. The Monday showers are fine. They note the new times on a card inside the cupboard. The engineer, told of the change, explains that a one-off weekly cycle is easy to forget when the household’s week changes, and suggests checking its day and time each time the clocks change. He adds that a household that is away for a week can switch the cycle off for the time being and restore it on return. The household writes both points on the card, beside the settings, so that they are visible at the next change. They also keep a spare copy of the card in the folder of papers for the system, in case the one by the cupboard is lost.

A schedule is easy to check when the clocks change in autumn, and again at the start of winter.

Good to know in Hendon

Hot water schedule

The times at which the heat pump heats the cylinder.

High-temperature cycle

A regular boost of the stored water to a higher heat, done to keep it safe.

Cylinder temperature

The heat the controller aims to bring the stored water to and maintain.

Questions about heat pump controls & optimisation in Hendon

01When should the cylinder heat?

Before the busiest use, finishing shortly before it.

02Why a weekly cycle?

To protect the water, and it should be set for a quiet time.

03How hot should the cylinder be?

Hot enough for comfort, not higher than needed.

04Can the schedule change by day?

Often yes. Set weekends differently.

05What should I do if the hot water falls short?

Adjust the timing or the temperature, and note the result.

Talk to Heat Go

Ask about heat pump controls & optimisation in Hendon.

Describe to Heat Go how your household uses hot water, with your Hendon address, and times to try first can be proposed.

The quickest way to talk to a Gas Safe, WaterSafe and G3 certified team is to call +44 7551 336264.

Heat pump controls & optimisation enquiry

What can we help with?

All fields marked * are required

We reply to the contact details you give. A UK number such as 07700 900123 works fine.