Heat pump controls & optimisation · Colindale

Heat pump controls in Colindale: frost protection settings for an empty flat between tenancies

A flat that stands empty for a few weeks still needs its heating system looked after. In a cold snap, water in the pipes and the cylinder can freeze, and a flat with no one at home will not notice until it is too late. A heat pump has frost protection and an away mode, and using them keeps the system safe at little cost. Landlords and agents in Colindale can set them as part of the routine between tenancies.

Certified for the work. Heat Go holds Gas Safe, WaterSafe, G3 and heating and plumbing certification. Call +44 7551 336264 to talk it through.

Gas Safe Register WaterSafe Heat Go G3 certified Heat Go Heating and Plumbing Engineer

Flats in Colindale with heat pumps have controllers and apps, and a plant cupboard on an internal wall. An empty flat loses heat from the neighbours’ side less than a house would, but a corner or top-floor flat can still get cold. The outdoor unit and pipes outside are the most exposed. The system must be left in a state that protects them.

A routine for an empty flat has six steps. Set the controller to away or holiday mode, with a low frost-protection temperature. Check that the circulation pump is set to run when the frost sensor calls. Make sure the outdoor unit’s power stays on, as switching it off may disable protection. Check the cylinder’s setting and the weekly cycle. Ask a neighbour or the agent to look in during a cold spell. And, on the day a new tenant arrives, restore the normal settings and run through the handover checklist.

Heat Go can set out a routine for the void period. Tell us how the flat is arranged, and a short checklist can be drafted.

Setting frost protection for an empty flat with a heat pump in Colindale

Void period questions in different Colindale flats

Top-floor flats with several outside walls

They lose heat faster. Check the frost setting and ask someone to look in during a cold spell.

Flats with the plant cupboard on an outside wall

The cupboard is colder. Make sure frost protection is active.

Flats where the app belongs to the outgoing tenant

Access passes to the landlord or agent. Reset it before the void period.

SettingParking and van accessProperty accessTypical enquiries
Top-floor flats with several outside wallsPermit zonesLiving roomExposed flats
Flats with the plant cupboard on an outside wallRoadsidePlant cupboardCold cupboards
Flats where the app belongs to the outgoing tenantDrives commonHallwayApp access

Give the agent the controller’s settings and a note of what to check during a visit. Tell the engineer if the flat will be empty over winter.

A landlord’s tenant leaves in November and the flat stands empty for a month. He sets the heat pump to away mode, with frost protection on, and keeps the outdoor unit powered. The agent calls in after a cold night and checks the controller, which shows the flat at seven degrees. When the new tenant arrives, the landlord restores the normal schedule and walks her through the cupboard. The pipes are sound. The agent, thanked for the check, asks whether the same routine could be used in other flats with heat pumps in the block, and the landlord shares the checklist. Before the next winter, the agent circulates a version to all owners, and a neighbour adopts it for her own empty flat when she goes abroad for a month. The checklist grows to a page and a half, and is kept with the property papers.

A void checklist is useful whenever a flat is empty in the cold months, and best made in autumn, before the first frost.

Good to know in Colindale

Frost protection

A setting that runs the heating at low level to stop pipes and the cylinder freezing.

Away mode

A setting that lowers the heating target while a home is empty.

Void period

The time between one tenant leaving and the next arriving, when a flat stands empty.

Questions about heat pump controls & optimisation in Colindale

01Should I switch the heat pump off in an empty flat?

No. Use away mode with frost protection.

02How low can the temperature go?

The installer sets the frost limit. Do not lower it further.

03Who checks the flat?

The agent or a neighbour, during cold spells.

04What about the app?

Make sure access belongs to the landlord or agent.

05What happens when a tenant arrives?

Restore the normal settings and do the handover.

Talk to Heat Go

Ask about heat pump controls & optimisation in Colindale.

Give Heat Go the flat’s layout and your Colindale address, and a short void-period checklist can be drafted.

The quickest way to talk to a Gas Safe, WaterSafe and G3 certified team is to call +44 7551 336264.

Heat pump controls & optimisation enquiry

What can we help with?

All fields marked * are required

We reply to the contact details you give. A UK number such as 07700 900123 works fine.